Following changes are included:
11abda9 - armv8: ls2080ardb: update copyright claim
7d5b814 - Revert "EHCI: Fix endian access issue on EHCI intinalization"
160deab - Revert "powerpc/T104xRDB: Fix endian access issue on EHCI intinalization"
007ac5c - Revert "powerpc/p1_p2_rdb_pc: Fix endian access issue on EHCI intinalization"
e82a7bc - LS1043ARBD: Fix SD Boot issue with PPA
ec7f4b3 - armv8: ls1088a: change dpl load address to 0x80001000 from 0x80000000
93bb79f - board: freescale: ls1012afrwy: Add LS1012A-FRWY board support.
aabf70f - board: freescale: ls1012afrx:Common files to support
da97a2b - watchdog: disable to build the driver in default
60afe56 - watchdog: Kconfig: add config to disable wdog reset
cf17a12 - watchdog: driver support for layerscape
6ac9ac0 - armv8: ls1088: change ttyS1 to ttyS0
0c9305b - boards: freescale: lsch3: Add 0.9v entry for vid
0346460 - armv8: ls1088a: change dpl load command from apply to lazyapply.
c43f05a - drivers/net/vsc9953: Initialize action RAM in VCAP complex
0a1adba - board: Kconfig: Re-Arrangement of PPA firmware and header addresses
ecf1d55 - arm: ls1021aqds: config: enable CONFIG_ID_EEPROM for mac command
4d94f28 - board: freescale: ls1012ardb: Add command to switch QSPI bank
cba0675 - driver/mtd/spi: Default page size Spansion flash "S25FS512S" is 256b
7c4f3c8 - LS1012AFRWY: Add Secure Boot support
51a93cc - board: move ppa header address in board specific kconfig
e26f485 - board: ls1012a: FRWY-LS1012A board support
d000b14 - board: move ppa firmware address in board specific kconfig
2f51b35 - armv8: ls1088a: Enable USB in ls1088ardb_sdcard_qspi_SECURE_BOOT_defconfig
842df34 - armv8/fsl-lsch2: make the workaround for PIN MUX erratum
A010539 robust
1fa9417 - armv8: sec_firmware: Add support for multiple loadables
eca9656 - armv8/fsl-lsch2: correct QMAN clock
c3a6ed4 - driver: net: fsl-mc: updated copyright info
39966d9 - armv8: ls1088a: Move CONFIG_BOOTARGS and CONFIG_CMD_GREPENV to defconfig
ccde7d9 - armv8: ls1088aqds: Enable mdio commands on u-boot prompt
9c912c7 - armv8: sec_firmware: Remove JR3 from device tree node in all cases
5ecc2f5 - mmc: fsl_esdhc: fix probe issue without CONFIG_BLK enabled
8ed20db - usb: Add delay to fix USB 2.0 stick enumeration failure on LS208xA
b133620 - EHCI: Fix endian access issue on EHCI intinalization
faf6feb - u-boot: fixup the iommu-map property of fsl-mc node
8e0c780 - powerpc: configs: Set initrd_high environment varible
Signed-off-by: Chunrong Guo <chunrong.guo@nxp.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
